English
HANDAN HAOSHENG FASTENER CO., LTD.

Chemical Anchors Bonded Injection Anchor Assemblies China Factory

Chemical Anchors Bonded Injection Anchor Assemblies China Factory

Looking for chemical anchors? HAOSHENG supplies bonded/injection anchor assemblies — threaded rod, nut, washer and anchoring adhesive matched as one set. Selection follows GB/T 37127-2018 (adhesive) and JGJ 145-2013 (post-installed fastening), with rod size, embedment and finish built to your drawing or project schedule. Carbon, alloy and stainless rods; ISO 9001/14001/45001 certified factory. Send base material and load requirements for a quote.

  • Description
chemical-anchors

Haosheng Fasteners supplies chemical anchors, also known as bonded or resin anchors. Each post-installed assembly is built from a threaded rod, nut, washer and anchoring adhesive, with adhesive cartridges and mixing nozzles supplied where required. Adhesive is injected into a pre-drilled hole in the concrete, the rod is inserted, and once the adhesive has cured the rod is bonded to the base material. These assemblies fix equipment bases, steel structures and brackets, pipe supports and guardrail base plates, curtain wall connectors and added connections on existing concrete structures during renovation and repair work.

There is no single dimensional standard covering complete chemical anchor products, and no fixed load value that applies to every size and installation. Anchoring adhesives for concrete structures can refer to GB/T 37127-2018, while design, installation and inspection of post-installed fastenings can refer to JGJ 145-2013 together with the project design documents and current applicable requirements. Rod diameter, embedment depth, hole diameter, concrete strength, edge distance, load direction, adhesive type and curing time all affect capacity. Rod material, strength class and surface finish come from the supplied product and its inspection documents; rod length, thread specification, adhesive type, packaging and accessories are built from your drawing, sample or project schedule, so the rod, adhesive and installation parameters reach site as one matched set rather than as loose parts.

Detailed Parameters

Product TypeBonded / Injection Chemical AnchorExecutive BasisProduct Documentation and Project Design
Assembly ComponentsThreaded Rod / Nut / Washer / AdhesiveRod MaterialsCarbon / Alloy / Stainless Steel
Rod SizePer Drawing or Project ScheduleEmbedment and HolePer Adhesive Data Sheet and Design
Adhesive ReferenceGB/T 37127-2018Design ReferenceJGJ 145-2013
Surface FinishesPlain / Electro-Zinc / HDG / CustomSamplesAvailable upon request

Technical note: There is no single dimensional standard that applies to all complete chemical anchor assemblies, and no universal load table. GB/T 37127-2018, Anchorage adhesive for concrete structure, is currently listed as valid on the National Public Service Platform for Standards Information (issued 2018-12-28, implemented 2019-11-01); its 2025-09-05 review concluded that a revision is needed and a revision project is in drafting, but no replacement edition has been published. Its scope covers the production, inspection and use of anchoring adhesives for concrete only, not a complete rod-and-adhesive anchor product. JGJ 145-2013, Technical specification for post-installed fastenings in concrete structures, is also current (issued 2013-06-09, implemented 2013-12-01, replacing JGJ 145-2004). It covers the design, construction and acceptance of post-installed connections in reinforced, prestressed and plain concrete and does not apply to masonry, lightweight aggregate concrete or special concrete substrates; some of its mandatory provisions have been superseded by the general codes GB 55008-2021 and GB 55021-2021, so the project design documents and current applicable requirements govern. On international projects, bonded anchors are commonly qualified against an ETA to EAD 330499 and designed to EN 1992-4, or assessed under ACI 318 Chapter 17 and ICC-ES AC308; the applicable approval documents for the specific product must be checked with the design. No load value is quoted here: capacity depends on rod diameter, material and strength class, embedment depth, drilled hole diameter and hole cleaning, concrete strength and cracking condition, anchor spacing, edge distance, load direction, adhesive type, installation temperature and curing time, and must come from test documentation for the specific product, engineering calculation or the project requirements. Drilling, hole cleaning, adhesive injection, rod insertion and curing must follow the instructions for the selected anchoring adhesive. These figures describe the scope of supply, not a stock list or a design value: rod dimensions, hole dimensions, embedment depth and curing time are confirmed against the applicable product documentation and the order drawing.

Key Advantages

Bonded Load Transfer

Cured adhesive bonds the rod along the embedment length instead of pressing an expansion sleeve against the borehole wall.

No Expansion Force

Bonded anchors create no wedge pressure, so spacing and edge distance are checked against the product approval and project design.

Matched Rod and Adhesive

Rod, adhesive cartridge, mixing nozzle, nut and washer are quoted as one compatible assembly, not as loose parts.

Material and Finish Choice

Carbon, alloy or stainless rods with plain, electro-zinc, hot-dip galvanized or custom finishes match the service environment.

Defined Installation Parameters

Hole diameter, cleaning method, embedment depth and cure time are stated from the adhesive data sheet before release.

Documentation-Led Selection

Capacity comes from product test documentation and engineering calculation, never from the threaded rod diameter alone.

Product Gallery

Management Platforms

Design Basis Review

Base material, concrete condition, load direction and required approvals are checked before quotation and drawing review.

Material and Class Control

Rod grade, strength class and surface finish are verified to the ordered specification and inspection documents.

Threaded Rod Production

Diameter, length, thread specification and end finish are cut and gauged to the drawing, sample or project schedule.

Adhesive and Accessory Matching

Adhesive type, cartridge format, mixing nozzle, nut and washer are matched to the rod and installation method.

Installation Parameter Control

Hole diameter, cleaning procedure, embedment depth and cure time are recorded from the adhesive data sheet.

Documentation and Traceability

Material certificates, test reports, batch records and samples can be written into the order for approval.

Standard and Specification Comparison

Comparison FeatureGeneric Rod-Only SuppliesHaosheng Chemical Anchor Assemblies
Selection BasisNominal rod diameter and length onlyProject design, product documentation and adhesive data sheet
Standard ReferencesNo distinction between adhesive and design codesGB/T 37127-2018 adhesive, JGJ 145-2013 application
Load CapacityOne value quoted for every sizeFrom product test reports and engineering calculation
Installation ControlGeneric drill-and-fix instructionHole cleaning, embedment, injection and cure per data sheet
Order InformationDiameter and quantityBase material, loads, hole, embedment, environment, quantity

Selection note: A chemical anchor is a system, not a single standard fastener. Before ordering, state the base material type and concrete strength, cracked or uncracked condition, load direction and magnitude, anchor spacing and edge distance, hole diameter and cleaning method, required embedment depth, installation temperature and allowed curing time, and the rod diameter, length, material, strength class and surface finish. Confirm the anchoring adhesive type and packaging, plus any cartridge, mixing nozzle, nut and washer requirements. Where the project calls for a specific approval or qualification scheme, have the engineer confirm the applicable product documentation before release; a product datasheet alone is not a design document. Because there is no universal dimensional table and no fixed capacity for all sizes, every dimension and performance figure must be taken from the selected product's technical documentation and the engineering design rather than from a generic stock list. For existing concrete, renovation and repair work, a site pull-out test or proof load may be required by the project specification, and drilling, cleaning, injection, insertion and curing must follow the selected adhesive's instructions.

Frequently Asked Questions

Q: Is there a single dimensional standard for chemical anchors?

No. A complete assembly combines a rod and an adhesive, so rod dimensions, hole sizes and embedment follow the chosen product documentation and the project design, not one common standard table.

Q: Can load capacity be determined from rod diameter alone?

No. Embedment, hole diameter and cleaning, concrete strength and cracking, edge distance, load direction, adhesive type and cure time all matter. Use product test documentation or engineering calculation.

Q: What does GB/T 37127-2018 cover?

It covers anchoring adhesives for concrete structures, including their production, inspection and use. It does not define a complete chemical anchor assembly or its dimensions and load ratings.

Q: How should JGJ 145-2013 be applied?

It guides design, installation and acceptance of post-installed fastenings in concrete. Apply it with the project design and current general codes; masonry and lightweight aggregate concrete substrates are outside its scope.

Q: What details should I send for a quotation?

Send base material and concrete strength, load direction, hole diameter and embedment, service environment, rod diameter and length, material, class, finish, adhesive type and quantity, or simply a drawing.

Q: Can you supply matched accessories, certificates and samples?

Yes. Nuts, washers, adhesive cartridges, mixing nozzles, material certificates, test reports and samples are available. ISO 9001, ISO 14001 and ISO 45001 certified production.

Need Chemical Anchors? Send Your Base Material and Load Requirements for a Quote.

Please include the concrete condition, load direction and magnitude, hole diameter, embedment depth, rod size, material, strength class, surface finish, adhesive type and quantity. A drawing or project specification helps us match the rod and adhesive.

Contact Us

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.