English
HANDAN HAOSHENG FASTENER CO., LTD.

DIN 439 Hex Thin Nuts for Tight Clearances: What to Check Before Ordering

17 November 2026

DIN 439 Hex Thin Nuts suit assemblies where a standard nut profile leaves too little room. Choose them by clearance, thread size and pitch, material, strength level, and finish.

Illustration: DIN 439 Hex Thin Nuts for Tight Clearances: What to Check Before Ordering
Illustration for reference; see the product page for actual photos and specifications.

DIN 439 Hex Thin Nuts suit assemblies where space is constrained and a standard nut profile is unsuitable. We supply the low-profile hex form in carbon steel and stainless steel, with metric sizes and coarse or fine thread options for fastening, thread protection, and assemblies with limited clearance.

Start with the available space

The first check is the room around the threaded joint. The reduced-height profile helps where a standard nut would interfere with nearby parts or where exposed threads need a compact protective nut. The hexagonal shape remains suitable for wrench engagement during assembly.

Choose this product when the joint has limited clearance above the nut or when a lower profile is part of the assembly requirement. DIN 439 Hex Thin Nuts fit locking mechanisms, thread protection, and other metric joints that need a compact hex nut.

Match the thread before choosing the finish

Thread size and pitch determine whether the nut will run onto the mating bolt or stud. Our range covers M1.6-M52 and includes coarse and fine threads. Check the nominal thread size and the required pitch on the mating part before ordering.

CheckDIN 439 Hex Thin Nuts options
StandardDIN 439
MaterialCarbon steel or stainless steel
Strength levels4, 8, 10, A2-70, A4-70, A4-80
Size rangeM1.6-M52
Thread optionsCoarse thread and fine thread
Surface finishZP, HDG, BLACK, Dacromet, and other options

For a replacement or production assembly, send the thread size and pitch together. The range includes small metric sizes such as M1.6 and larger sizes through M52, so the nominal diameter alone should not identify the order line.

Select material and strength for the joint

Carbon steel fits assemblies specifying a carbon-steel nut, while stainless steel is available when the joint calls for a stainless-steel option. Choose the strength level to match the mechanical requirement of the mating fastener and the joint design. The available strength levels are shown in the table above.

Material and strength are separate from the low-profile shape. You may need the DIN 439 geometry for clearance while also matching the nut's material and strength level to the rest of the fastening system.

Treat the finish as part of the order

Include the surface finish when the assembly has a specified coating or appearance requirement. The available options are shown in the table above. State the finish with the material, strength level, thread size, and pitch.

This identifies the requested nut by its complete combination, not by “DIN 439” alone. It matters when the same thread size is used in more than one finish or material.

What to weigh

Clearance · confirm the joint needs a reduced-height nut profile.

Thread fit · match metric size and coarse or fine pitch.

Material and strength · select carbon steel or stainless steel with the required level.

Finish · state the selected coating or appearance option with the order details.

Your shortlist

DIN 439 Hex Thin Nuts · clearance-sensitive assemblies, thread protection, and metric joints needing a low-profile hex nut.

Who should choose DIN 439 Hex Thin Nuts

Choose DIN 439 Hex Thin Nuts when your assembly needs a reduced-height nut for limited clearance, a hexagonal form for wrench engagement, compact thread protection, or coarse and fine metric threads. Carbon steel and stainless steel options support different material requirements.

Before placing an order, measure the available clearance, identify the mating thread size and pitch, then specify the material, strength level, and surface finish.

The company

HANDAN HAOSHENG FASTENER CO., LTD.

Founded in 1996, is a large and professional manufacturer of high-strength fastener. Our factory located in Yongnian County,Handan City, Hebei Province, China,covers an area of 20000 square meters. Now we have advanced cold-forged machine,heat treatment machine and spheroidizing annealing equipment,most of which imported from Taiwan .Output is over 2000 tons every month.

About Us ↗Visit company website ↗

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.